Purpose-built monitoring solutions — wireless point sensors, fibre-optic distributed temperature sensing (DTS) and transmission-line sensors — for energy, oil & gas, mining, buildings and industry.
Wireless temperature and environmental sensors, data collectors and the AI platform for substations, power plants and switchgear.
Full oversight of transformer stations — temperature, humidity and thermal condition of every critical device — to prevent unplanned outages.
Supervise temperature and humidity levels for devices within electrical generation facilities and extend equipment lifespan.
Track temperature and humidity throughout refrigerated supply chains — protecting pharmaceuticals, food and sensitive goods.
Track thermal conditions inside medium-voltage equipment cabinets where hidden hotspots often go unnoticed until failure.
Monitor, measure and manage energy performance to improve efficiency and meet international energy-management standards.
Fibre-optic DTS for buried and long-run cables — a continuous thermal profile alongside point sensors. One armoured fibre gives a continuous temperature profile every 0.5 m over kilometres, with no electrical power and no electronics in the field.
Data centres, high-rise commercial buildings, hospitals, metro systems and large factories
The sensing fibre runs along the full length of the busway, including every joint and tap-off. Loose or oxidised joints show up as a local temperature rise against the neighbouring sections, long before insulation damage or a busway fire. One controller covers up to 4 busway risers or runs.
Refineries, terminals, tank farms, LPG bottling plants, pipeline operators
Continuous temperature profiling along pipelines, on storage tank shells, floating-roof rim seals and LPG spheres. Abnormal heating or cooling points are located to within metres, for early fire detection and leak indication where the product temperature differs from ambient (heated crude, steam, LPG/LNG). The sensing fibre is passive – no electrical energy in the hazardous area – and the optical source is certified Ex op is (inherently safe optical radiation) to IEC 60079-28. 16 relay outputs can trigger fire-suppression or shutdown interlocks.
Monitoring of reactors, process piping, tank farms and cable trays in process areas, with zone-based alarms on a plant GIS map and direct interlock to fire-protection systems.
Coal and mineral mines, steel plants, cement, ports, power plant coal handling
Kilometres of conveyor belt monitored with one fibre: idler and roller bearing overheating, belt friction and spontaneous coal ignition are detected and located before they become a fire. Armoured cable rated ≤ 5000 N/10 cm crush, for harsh environments and underground tunnels.
Power cable tunnels, trenches and trays
HV cable overheating, insulation breakdown and fire detection — in underground high-voltage transmission cable tunnels and substation trenches, with metre-level accuracy.
Splices, dead-ends and lug landings on 110–500 kV lines — hot-spot detection and inputs for dynamic line rating.
VTI-TS-26 provides measured temperature of conductor connections (splices, dead-ends, jumpers), for hot-spot detection and as a real-time input to the utility’s DLR / ampacity calculation (IEEE 738, CIGRE TB 601). The rating calculation also needs weather data and the utility’s own rating engine.
Generation, transmission and distribution infrastructure — from power plants and substations to transmission-line corridors.
Refineries, terminals, tank farms, LPG bottling plants, pipelines and chemical plants — continuous fibre-optic temperature profiling for early fire detection and leak indication.
Coal and mineral mines, steel plants, cement, ports and power plant coal handling — kilometres of conveyor belt monitored with one fibre.
Plants and facilities that rely on early fault detection, predictive maintenance and process safety to stay productive.
Electrical distribution systems in multi-story apartments & commercial malls, ensuring continuous thermal monitoring and safety across switchgears, busways / busducts, busbars and panels.
Temperature-sensitive environments such as hospitals, laboratories and pharmaceutical cold chains that demand continuous assurance.
A clear, proven process that takes you from assessment to a fully supported, running system.
We understand your assets, risks and existing systems to define the right monitoring strategy.
We design the solution and source proven technology through our international partners.
Sensors, sensing fibre and gateways are installed — clamp-on sensors during a planned outage — and integrated with the AI platform and SCADA.
You get 24/7 monitoring, alerts and ongoing support to keep operations running smoothly.
Talk to our team about wireless sensors, thermal imaging and AI-driven monitoring tailored to your operations.